Home > Browse All Products > Drones & Flight >

  Crazyflie Nano Quadcopter Kits (10-DOF)
Crazyflie Nano Quadcopter Kits (10-DOF)
Crazyflie Nano Quadcopter Kits

Alternative Views:

Our Price: $177.99

Availability: Usually Ships in 1 to 2 Business Days
Product Code: MKSEEED14

Description How To More Details

The Crazyflie Nano Quadcopter Kits are open source, and designed for flexible development and hacking. It's among the smallest in the world, weighing only 19 grams and measuring 9 cm motor to motor. This thing is tiny.

Due to itís small size itís perfect for developing new software and can easily be flown inside. It can lift a payload of up to 5-10 g. This 10 DOF version integrates sensors for altitude and heading measurement as well.

The Crazyflie is open source, so schematics and firmware/host source code is available at the Bitcraze website as well as a Wiki with design information and details on how to set up the development environment and get started. Itís designed with development in mind and has an expansion header that enables developers to expand the platform.

Please note: this kit requires soldering for assembly and is not recommended for beginners. In order to get flying, a few items that aren't included in the kit are needed. Please see the "more details" tab above for more.
  • Small and lightweight, around 19g and about 90mm motor to motor
  • Flight time up to 7 minutes with standard 170mAh Li-Po battery
  • Standard micro-USB connector for charging which takes ~20min for the stock 170mAh Li-Po battery
  • On-board low-energy radio@1mW based on the nRF24L01+ chip. Up to 80m range (environment dependent) when using the Crazyradio USB dongle
  • Radio bootloader which enabled wireless update of the firmware
  • Powerful 32 bit MCU: STM32F103CB @ 72 MHz (128kb flash, 20kb RAM)
  • 3-axis high-performance MEMs gyros with 3-axis accelerometer: Invensense MPU-6050
  • 3-axis magnetometer HMC5883L (compass)
  • High precision altimeter MS5611-01BA03
  • Expansion header 2◊10 pins 1.27mm (0.05Ē) pitch including power, I2C/UART, SPI/ADC. Header also contains ARM Cortex 10-pin JTAG (header not included)
  • 4-layer low noise PCB design with separate voltage regulators for digital and analog supply

Average Customer Review: 3.5 of 5 | Total Reviews: 3 Write a review.

Related Products:
ELEV-8 Quadcopter
Sale Price: $564.99

ELEV-8 Quadcopters
Make Getting Started with Soldering Kit
Our Price: $64.99

Make: Getting Started with Soldering Kit

  2 of 3 people found the following review helpful:
No directions with the copter. Incomplete website February 22, 2014
Reviewer: Michael Lloyd from Weimar, TX United States  
There is a 5 pin header in the package and do directions for what to do with it.

I've tried 2 motors for motor #2 and it does not spin during POST. Soldering in a second motor is orders of magnitude more difficult than installing the original motor and that is very hard to do. You cannot do it without some sort of lighted magnifier.

Was this review helpful to you?

  1 of 3 people found the following review helpful:
Great product, controller difficult to configure February 13, 2014
Reviewer: Alexi from Durango, CO United States  
Configuration of a input controller is difficult and a bit spotty. I found it hard to get good instructions on setting up a game controller to fly this guy. I tried Ps4 USb, Xbox BT and USB on PC and linux and could not get any to work with software right away. I followed the wiki instructions.
I did finally get the Ps4 controller to work with PC. Yaay.
I was starting to get a hang of it.
Crashed the little guy, not too hard I thought.. seemed like a light crash, but now the Nano stopped working. Wondering if something happened to the chip or a connection on the micro-controller.  Debating getting another but wish the price was a bit more reasonable for such a delicate quadcopter.

Was this review helpful to you?

  3 of 3 people found the following review helpful:
Awesome! December 28, 2013
Reviewer: Sidney from Santa Monica  
This product is great. It was a ton of fun to put together. I am currently learning how to fly it (there is a bit of a learning curve) then I will start on the coding. As far as the controller is concerned in the is other guys comment, yes the controller set up may not be easy. I said "may" because if you already have your comp set up to work with a PS3 paddle then it'll be as easy as plug n play. Otherwise (like my case for example) you have to download the Motioninjoy software, and drivers, to get your controller working. There aren't many tutorials out there on how to do this so again there is a bit of the curve, but isn't that a part of the fun? I definitely recommend this little quadcopter, just make sure you have some patience before you start

Was this review helpful to you?

Browse for more products in the same category as this item:

Browse All Products > Drones & Flight
Browse All Products
Level > Advanced
Sign up for our newsletter to receive exclusive deals and discounts