Maker SHED

Login My Account Help

Shopping Cart:

(Your shopping cart is empty.)

Home

Weekly Deal

Shipping Info

Home > Browse All Products > > Arduino & Microcontrollers > Arduino Boards, Shields, and Accessories > Arduino-Compatible Shields >

Official Arduino Motor Shield

Alternative Views:

Our Price: $30.00

Availability: Usually Ships in 24 to 48 Hours
Product Code: MKSP12

Qty:

Description

How To

More Details

If you're planning to build a robot with an Arduino, you'll likely need a motor shield to drive your motors! This Official Arduino Motor Shield fits right on top of your Arduino Uno (or compatible) microcontroller and uses a full-bridge L298 driver. The L298 driver is capable of providing 2 channels with 5-12V at 2 amps per channel (or 4 amps max with external power supply) to control inductive loads such as relays, solenoids, and DC or stepper motors. It's perfect for robotics because it is able to control the speed and direction of two DC motors independently, as well as measure the current each motor is using. This means that you can use your motors as an input device by measuring changes in current flow. Did your robot just hit a wall? With the right programming, your Arduino will sense the sudden rise of current from the stalled motors and command your robot to reverse to safety. The shield also features braking so you can stop your robot quickly should the need arise.

Because the Arduino Motor Shield draws a lot of power it must be hooked up to an external 7 - 12V power supply rather than a USB connection to avoid damage. If your motors require more than 9V it is recommended that the power supply lines for the Arduino and the Motor Shield be separated and the "Vin Connect" jumper on the back of the board be cut.

Note: Standard servos will not work on this board.

Power

The Arduino Motor Shield must be powered by an external power supply because the L298 IC mounted on the shield has two separate power units, one for the logic and one for the motor supply driver. The current draw for the motor supply is often than the USB can give.

External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The adapter can be connected by plugging a 2.1mm center-positive plug into the Arduino's board power jack on which the motor shield is mounted or by connecting the wires that lead the power supply to the Vin and GND screw terminals, taking care to respect the polarities.

To avoid possible damage to the Arduino board on which the shield is mounted, we reccomend using an external power supply that provides a voltage between 7 and 12V. If your motor require more than 9V we recommend that you separate the power lines of the shield and the Arduino board on which the shield is mounted. This is possible by cutting the "Vin Connect" jumper placed on the back side of the shield. The absolute limit for the Vin at the screw terminals is 18V.

The power pins are as follows:

Vin on the screw terminal block, is the input voltage to the motor connected to the shield. An external power supply connected to this pin also provide power to the Arduino board on which is mounted. By cutting the "Vin Connect" jumper you make this a dedicated power line for the motor.
GND Ground on the screw terminal block.

The shield can supply 2 amperes per channel, for a total of 4 amperes maximum.

Input and Output

This shield have two separate channels, called A and B, that each use 4 of the Arduino pins to drive or sense the motor. In total there are 8 pins in use on this shield. You can use each channel separately to drive two DC motors or combine them to drive one unipolar stepper motor.

The shield's pins, divided by channel are shown in the table below:

Function	pins per Ch. A	pins per Ch. B
Direction	D12	D13
PWM	D3	D11
Brake	D9	D8
Current Sensing	A0	A1

If you don't need the Brake and in the Current Sensing and you also need more pins for your application you can disable this features by cutting the respective jumpers on the back side of the shield.

The additional sockets on the shield are described as follow:

Screw terminal to connect the motors and their power supply.
2 TinkerKit connectors for two Analog Inputs (in white), connected to A2 and A3.
2 TinkerKit connectors for two Aanlog Outputs (in orange in the middle), connected to PWM outputs on pins D5 and D6.
2 TinkerKit connectors for the TWI interface (in white with 4 pins), one for input and the other one for output.

Motors connections

Brushed DC motor. You can drive two Brushed DC motors by connecting the two wires of each one in the (+) and (-) screw terminals for each channel A and B. In this way you can control its direction by setting HIGH or LOW the DIR A and DIR B pins, you can control the speed by varying the PWM A and PWM B duty cycle values. There are also the Brake A and Brake B pins that if setted in HIGH state they brakes the DC motor faster than when you power off the motor. You can know the current going through the DC motor by reading the SNS0 and SNS1 pins. On each channel will be a voltage proportional to the measured current, which can be read as a normal analog input, through the functions analogRead() on the analog input A0 and A1. For your convenience it is calibrated to be 3.3V when the channel is delivering its maximum possible current, that is 2A.